Hi people I'm new to this forum. I'm a hardware engineer and i bought some Xilinx FPGA evaluation boards, including and XUP-V2P, for hobby purposses. I never...
... The only issue I think you'll have is the SDRAM controller, as the configuration of the SDRAM on the DE2-70 differs from the DE2. I have ported the DE2 to...
I am happy to let you people know the status of this thread. Yesterday, I could get Minimig running stable on my DE1. I worked with revision E new, booted with...
I have never seen a picture from a minimig with a 2.04 bootscreen. But the minimigtg68 can boot all versions of kickstartrom. Now I found a little but...
... I have vague memories of some old screenshots showing kick3.x bootmenu http://home.hetnet.nl/~weeren001/files/Minimig_proto_blit_trouble.JPG ... You have...
Anyone tried? Anyone working at it right now? I own a Digilent Microblaze Starterkit and would really like to be able to boot an Amiga on it. It comes with a...
Magnus Wedmark wrote: Hi everyone... ... Digilent seems to have removed this board from its page -- so I can't verify: But isn't this board the big brother of...
... get over.. ... You are correct! It is DDR-memory and the 1600 is a "bigger brother" of the more common 3E-Starter Kit with its 500K-device. Thank you for...
hi, I am following this thread... You will find a sopc project using the controller here : https://roulette.das-labor.org/bzrtrac/wiki/soc-lm32 -- ... -- -- ...
Magnus Wedmark wrote: Hi, ... I'm actually the author... and I've seen some examples of it being in use :) None of them was actually small... But it does...
... One (other) obstacle you'll face in using another DDR controller in Minimig is that the controller needs to arbitrate between 68K and Z80 accesses - so ...
Mark McDougall wrote: Hello, ... Could you sum up the requirements for the minimig SDRAM access? (operating frequency; maximal latency: data width.. ) Sorry...
Here you can see the fist try to make the minimigtg68 faster: http://gamesource.ph.groups.yahoo.com/group/minimigtg68/photos/view/d50 8?b=2&m=f&o=0 or if the...
... Wow!!! Your work is impressive! :-) Even if SysInfo is not the best Amiga benchmark I guess that your core gives more accurate speed than emulators... so...
... http://gamesource.ph.groups.yahoo.com/group/minimigtg68/photos/view/d 50 ... design and ... core ... on A500? ... hardware ... It isn't a new 68K Core. But...
I tried that a couple of weeks ago, but did not get the expected result. I've only tried it in a Basic test but I had problems getting the lm32 to run on my...
On http://www.amiga.org riftcon, piru and i discuss about the 68sec000. Now it look like the 68SEC000 is a 68000. The "Move from CCR" is illegal and "Move from...
Hello, Now I call my Amiga core with the Minimig Chipset and the TG68 "FAMPIGA". Please use the Files Version 13. Please test the new Future! Now you can write...
Hi TobiFlex and fellow FPGA Enthusiasts :- I know this is some what off topic but do you have Altera DE1 HDL for the CPC ??? I can find you mentioned with a...
I am also interested in the CPC core, it would be nice to it for DE1. ... -- -- Visit my personal page: http://ronivon.costa.googlepages.com/ -- Ronivon C....
Hello, i have done it a year ago. Based on Tobiflexs DE2 Code. You can download it from: http://drunken.intershit.com/cpctrex_DE1_Port1.rar So far no SD card...
... files. ... Feedback ... Hello, I tested it with the new spihost.rom, but it does not work. The new spihost.rom works in the 12e version. Can you release...
Hello, I have not the Time to do this yet. First I will fineshed the new Startup System for the C-One. Sorry. Viele Grüße TobiFlex ... for ... find ... and ...
Tell me more about your Problem, Please. You must use the new spihost.rom firmware and the minimig_de1.sof to config the 2c20. The are only little changes...
... Hello, I use the pof file from v13 to check, after I flashed the DE1 the minimig does not start. I checked again using the 12e version, this works. As test...
Hello, I checked my setup again - and it works with the .pof and with the .sof that i have published. Please reformat your SD Card copy the files and try it...
Hello, Sorry I overlooked the source files. Compiled the new version and tested Little Computer People, the program starts but still testing the write to...
Hi, Can anybode recommend an easy way to create the daughter board for connecting the mouse and the joystick? The Fampiga runs fine, it runs the same demos as...
I currently do not have a board to run this project on. Should I get the more expensive DE2 or is the DE1 fine? How much FPGA space does the current...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
