... combines ... and ... Hello Dennis, I have finished the address decoder. I have 70+ write strobe signals out of it and a big mux for the register read. I...
... As far as I know (haven't tried Tobiflex' core yet), the DE1/DE2 version uses the same basic firmware as the Minimig rev1.1. That means that you can scroll...
... days to ... hbeam ... delay ... 8.5 ... approach : I ... one ... is ... flip- ... comparator ... depending of ... logic" ... Hi Frederic, That sounds very...
... Hi Dennis, Nice to know you are around here! I've also been tinkering with modifying the code for ECS compatibility, though I suspect Frederic is...
... Hello Dennis, I am currently rewriting minimig with AGA/AAA features. So far, I have done the video beam controller with all the ECS/AGA registers. IMHO,...
Nice to see all the active development going on here! If you have any questions regarding Minimig, feel free to ask. Mathesar77 (aka Dennis @ Amiga.org)...
... From memory, I don't think I have ever formatted this SD card. I bought it - a micro SD in an SD adapter - to use on another FPGA project but it turned out...
Hi All, ... blits" Just starting to add support for ECS. Have added : 05C BLTSIZV - Blitter V size (for 15 bit vertical start) 05E BLTSIZH - Blitter H size...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minimigtg68 group. File : /Blitter.v ...
minimigtg68@yahoogrou...
Dec 25, 2007 12:04 pm
66
Ok, could just confirm that I have a problem with my LCD. When I turn it on whit minimig booted, I can see the kick start screen in a flash ... It appears for...
Ok, now I am getting something a little bit different, actually, as described by Mark. Then, I did as suggested by Laptev, and formatted one of my SD using my ...
Hi All, See a few folks are having problems with SD cards which may have been formatted using FAT under windows. I have 2 identical 512MB cards from Toshiba. ...
With different kickstart version, i get different results for adf loading. Some adf files which were not recognized with kick 1.2 are recognized with kick 1.3...
... disk! ... Engineers do it ... resistance!" ... Where is formatted your SD-card ? I format SD-Card in windows_XP, selected FAT. I`m too can`t boot any disk...
... I get this.... SPI card found! FAT16 found! Loading SPIHOST... Start SpiHost Start FDC EMU And then the Kickstart screen. But I can't boot any disks... ...
... MB with SD ... screen keep ... debug ... It is no problem in SD-card. Black screen keep in my DE1 only without SD-card. debug message - without SD-card ...
Ok, here it is what I get on the RS232 terminal: -- SPI card found! FAT16 found! Loading SPIHOST... Start SpiHost -- I got this for all sd cards I have (event...
I will try that this weekend, and let you know... I did not know there was debug messages send to rs232. thanks ... -- -- Ronivon C. Costa IBM TIVOLI Certified...
... Today I added some timing constraints to the above for the SDRAM pins. In particular, I tried adding tpd=11ns to all lines. It didn't quite meet timing,...
Hi Roni, ... (other ... Is your Kick.rom file 256kb or 512kb ? The SPIHOST expects a 512kb kickstart image. If your file is 256kb, just join two copies...
Sorry for the previous post... my cat jumped onve the Enter key on my keyboard... :D:D:D So, I have tested wih 2 SD cards, both formated as FAT on Windows XP...
Ok, here it is a sttus on my try in minimig... I have tested wih 2 SD cards, both formated as FAT on Windows XP (other option available isFAT32): - Lacor SD...
Hi all, I'm fairly certain there are timing-related problems with Minimig that won't be corrected until the gated clocks are eliminated and/or the correct...
... Forgot to say that perhaps it would be good to test out the audio adf file on a minimig with a hardware 68EC000 minimig in order to perhaps isolate the...
... Hi check out my last post about ProTracker, there are some serious bugs there. Also see "Photos"/"HeXaCrypt" for Sprite#0 error and blitter fill issues....
Hi All, Was having a look at the list at: http://www.opencircuits.com/Minimig_Software_compatibility to see which programs fail under original Minimig. Since...
Hi Roni, ... on my ... Signal coming out with SW9 ON should be 31.6kHz x 50.5Hz, not far off the normal VGA frequencies, but I have one LCD here which won't ...
Hi Everybody, especially TobiFlex this time =) We have tried out the ProTracker 3.15 software on the Altera DE2 board using the latest 12e_new posted earlier...
Hi Costa If you send send me a mail at hexacrypt@{no-spam}hotmail.com I can help you get started with some quick suggestions. (ps. remove the no spam part ds.)...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
